慕容各级师傅的机器人路径

慕容劈劈(ppclark@ts)

适用于论坛上luck版本的机器(师傅变量为master,去学习的别名是startxuexi,学完回来的别名是finishxuexi  )

所有路径都是直接拷贝了,然后再命令行里输入就可以了



先来个 慕容博 的

master=bo;#al startxuexi {s;w;n;n;w;w;w;w;w;w;sw;sw;w;w;sw;sw;w;w;w;ta;setdo {s;s;s;s;s;s;s;s;s;s;s;s;w;w;w;ta;setdo {ask ying gu about start;bbb {e;e;e;n;n;n;n;n;n;n;n;n;n;n;n;e;e;e;ta;setdo {ne;ne;e;e;ne;ne;e;e;e;e;e;e;s;s;e;n;ta;setdo {s;w;#9 n;ta;setdo {#2 ne;#6 n;w;ta;setdo {unwield @fight_weapon;nu;wu;#3 nu;#2 wu;#2 nu;wu;nu;n;n;knock gate;#2 n;ta;setdo {#5 n;n;nu;#4 n;e;n;w;ta;setdo {n;nu;n;e;e;ne;se;e;jump xiaoxi;enter;up;tui chuang;jump chuang;s;ta;setdo {#t+ xuexi;#va xx 1;#t+ 11;bai @master}}}}}}}}}}};#al finishxuexi {#t- xuexi;#t- 11;#va flagpot 0;n;jump out;d;out;jump xiaoxi;w;nw;sw;w;w;s;sd;s;w;s;ta;setdo {sw;s;e;s;s;sd;s;s;s;s;s;s;s;open gate;#3 s;ta;setdo {sd;ed;sd;sd;ed;ed;sd;sd;sd;ed;sd;e;#4 s;ta;setdo {s;s;#2 sw;#9 s;e;n;ta;setdo {s;w;n;n;w;w;w;w;w;w;sw;sw;w;w;sw;sw;w;w;w;ta;setdo {s;s;s;s;s;s;s;s;s;s;s;s;w;w;w;ask ying gu about over;bbb {e;e;e;n;n;n;n;n;n;n;n;n;n;n;n;e;e;e;ta;setdo {ne;ne;e;e;ne;ne;e;e;e;e;e;e;s;s;e;n;ta;setdo {firstjob}}}}}}}}}

慕容劈劈(ppclark@ts)

慕容复的

master=fu;#al startxuexi {xy-yg;ask ying gu about start;ta;setdo {yg-xy;#wa 2000;gcj;dj do;setdo {out;gmr;push 桥栏;d;yanziwu;s;e;ask fu about 俸禄;#wa 3000;ta;setdo {bai @master;#t+ xuexi;#va xx 1;#t+ 11}}}};#al finishxuexi {#t- xuexi;#t- 11;w;n;zuan didao;out;bmr;dj do;setdo {out;#6 n;#11 w;n;#wa 2000;xy-yg;ta;setdo {ask ying gu about over;bbb {#va flagpot 0;yg-xy;ta;setdo {firstjob}}}}}

慕容劈劈(ppclark@ts)

公冶乾的

master=gan;#al startxuexi {xy-yg;ask ying gu about start;ta;setdo {yg-xy;#wa 2000;gcj;dj do;setdo {out;gmr;push 桥栏;d;yanziwu;s;e;ask fu about 俸禄;#wa 3000;s;s;ta;setdo {bai @master;#t+ xuexi;#va xx 1;#t+ 11}}}};#al finishxuexi {#t- xuexi;#t- 11;n;n;w;n;zuan didao;out;bmr;dj do;setdo {out;#6 n;#11 w;n;#wa 2000;xy-yg;ta;setdo {ask ying gu about over;bbb {#va flagpot 0;yg-xy;ta;setdo {firstjob}}}}}

慕容豆豆(swiss@ts)

ppclark真是好人呀~~~~~造福MR